MTW series grinding mills obtain international advanced technology as well as many proprietary intellectual property rights.The electric system adopts centralization of control. Feed size is small and light that save the energy. The standard configuration of MTW Grinding Mill consists of main unit, powder classifier, blower, elevator, feeder, hopper, cyclone collector, dust catcher, blower, motor, pipe, electric control box and so on. Based on the years’reseach experience and the suggestion of our customer, the MTW series is the latest grinder .The MTW grinding mill adopt bevel gear integral transmission, inner light-oil lubrication system, arc whirl tube and other latest technologys.And now it has been used In the field of Metallurgy, building materials, chemical, mining and can be applied to crush the materials like Quartz, feldspar, calcite, talcum, barite, fluorite, rare earth, marble, ceramics, bauxite, manganese ore, iron ore, copper, phosphorus ore, zircon sand, slag, water, slag, cement, etc. MTW Grinding Mill widely used in metallurgy, building materials, chemicals, mining minerals in areas such as grinding materials processing. According to the fine grinding of materials and discharging materials fineness.

Working Principle of MTW Grinding Mill

The grinding mill is driven by rotation of the central axle through gear, with the up end of the axle connecting to a quincunx-rack upon which the grinding equipment is fixed. The whole set equipment turns together with the axle along the grinding ring while the rollers rotate driven by the fractional force .A set of shovel are installed at the lower end of the quincunx-rack.While turning together with the rollers, the shovels shed the stuff onto the gap between the rollers and the ring, and that’s where the stuff layer forms .The rotating rollers, while turning together with the ring, grind the stuff layer into powder. And the turning speed of the impeller can be adjusted to the requirements of the fineness of powder products .You must speed the impeller speed if you want to get the finer particle size .You can increase the contact between the impeller and the powder, which can make the non-conformance powder thrown to the outside wall, thus separating from the air stream.And the coarse powder will fall into the grinding room to be recrushed while the conformance final products will be intaked in the large classifier by the impeller.

MTW series grinding mills obtain international advanced technology as well as many proprietary intellectual property rights.The electric system adopts centralization of control. Feed size is small and light that save the energy. The standard configuration of MTW Grinding Mill consists of main unit, powder classifier, blower, elevator, feeder, hopper, cyclone collector, dust catcher, blower, motor, pipe, electric control box and so on. Based on the years’reseach experience and the suggestion of our customer, the MTW series is the latest grinder .The MTW grinding mill adopt bevel gear integral transmission, inner light-oil lubrication system, arc whirl tube and other latest technologys.And now it has been used In the field of Metallurgy, building materials, chemical, mining and can be applied to crush the materials like Quartz, feldspar, calcite, talcum, barite, fluorite, rare earth, marble, ceramics, bauxite, manganese ore, iron ore, copper, phosphorus ore, zircon sand, slag, water, slag, cement, etc. MTW Grinding Mill widely used in metallurgy, building materials, chemicals, mining minerals in areas such as grinding materials processing. According to the fine grinding of materials and discharging materials fineness.

Working Principle of MTW Grinding Mill

The grinding mill is driven by rotation of the central axle through gear, with the up end of the axle connecting to a quincunx-rack upon which the grinding equipment is fixed. The whole set equipment turns together with the axle along the grinding ring while the rollers rotate driven by the fractional force .A set of shovel are installed at the lower end of the quincunx-rack.While turning together with the rollers, the shovels shed the stuff onto the gap between the rollers and the ring, and that’s where the stuff layer forms .The rotating rollers, while turning together with the ring, grind the stuff layer into powder. And the turning speed of the impeller can be adjusted to the requirements of the fineness of powder products .You must speed the impeller speed if you want to get the finer particle size .You can increase the contact between the impeller and the powder, which can make the non-conformance powder thrown to the outside wall, thus separating from the air stream.And the coarse powder will fall into the grinding room to be recrushed while the conformance final products will be intaked in the large classifier by the impeller.